Thursday 31 May 2012

PANEL METER


PANEL METER

Panel meters                     

Electrical measuring instruments:
A measuring instrument is intended to measure an electrical and non-electrical quantity using electrical means.

Analogue measuring instruments:
A measuring instrument intended to present or display the output information as a continuous function of the measured quantity.
Indicating instruments
A measuring instrument displays at any time the value of measured quantity without recording it.

Permanent magnet moving coil instruments
An instrument which operates by the interaction of the magnetic field due to a current in a movable coil with the field of a fixed permanent magnet.

Moving coil with rectifier type instruments
Moving coil instruments cannot be used for measurement of AC current/voltage. For use on AC application, the AC input is given to moving coil instruments through full wave bridge rectifiers which converts AC into pulsating DC. Basically these meters read average value which is calibrated to read RMS value. Thus if there is any change in wave form is distorted, the calibration may not remain valid and the readings shown by the instruments may not be correct.
Moving iron instruments
An instrument which operates by the attraction between a movable piece of  ‘soft ‘magnetic material and the field due to a current in a fixed coil or by repulsion (and attraction) between one or more fixed pieces of soft magnetic material  and a movable piece of soft magnetic material , both (all magnetised by a current in a fixed coil).

Construction:
Moving coil instruments:
These instruments are used for DC current and voltage measurement. They measure average value of the input quantity.
The movement consists of a diametrically oriented cylindrical permanent magnet and a coil wound on aluminium coil former which is suspended on non-magnetic stainless steel pivots between two springs loaded sapphire jewel bearings.
When an electric current is passed thru the coil, a magnetic field is produced. This field interacts with the magnetic field of permanent magnet. The torque produced deflects the coil former along with the attached pointer, showing the reading on dial.

                  


Controlling torque is provided by  two spiral phosphor bronze hair springs, connected at both ends of coil which also provides   a connection to complete the current path through coil.
Damping is achieved with the help of eddy current s which are produced in an aluminium coil former rotating in the magnetic field of permanent magnet.. since the deflecting torque is directly proportional to the current following through the coil, the scale is linear.
A shield is provided to protect the movement against external magnetic field due to and to provide a low reluctance path for magnetic flux.

Moving iron instrument:
These instruments are normally used for measurement of AC current and voltage. A movement having spindle with moving iron, fixed iron and compensating iron is situated inside a copper coil. When current follows through the coil, it produces the magnetic field. The irons inside the coil core gets repelled away from fixed iron.
A pointer fixed on the spindle, on which a moving iron is fixed, gets deflected showing reading on the dial.
Controlling torque is provided by spiral phosphorus bronze hair spring.
Pointer comes to rest at equilibrium where deflecting torque and controlling torque becomes equal and opposite.
Damping is achieved by the use of jewel bearing with silicon coil.
Since the deflecting torque is directly proportional to the squire of current flowing through the coil, the nature of the scale is highly non linear in the conventional design of the moving iron meter.
The scale can be made linear by using specially designed movement, introduction of third iron, called compensation iron and specially designed shield.

Following types of meters are used in panel-
1.      Ammeters
2.      Voltmeters
3.      Frequency meters
4.      Power factor meters
5.      Maximum demand ammeter
6.      KW meters
7.      KVAR meters

Power factor meter
This instrument is used to measure power factor (cosine of angle between current and voltage vectors) of the supply. These are available in two types:
·         Electrodynamometer type
·         Electronic transducer type
Frequency meters
These meters are used for measurement of supply frequency.
These are available in two types:
·         Pointer type
·         Vibrating reed type
Pointer type frequency meters are available as electronic transducer which may be built in the meter.
Maximum demand ammeter
These meters have a bi-metal movement which is fully compensated against variations in ambient temperature. When current follows through the spring, due to unequal expansion of the two different bi-metals, a torque is created by the spring which is directly proportional to RMS current following through the spring. This torque in turn produces rotation off a spindle on which a pointer is fixed. Pointer indicates the value of RMS current on a printed scale.

The bi-metal is so designed that the full deflection is obtained after either 08 or 15 minutes of current that follows through the bi-metal spring depending on meters selected.  The trailing red pointer which gets pushed by measuring pointer when the current increase and remains in the same position unless it is rest to zero by external zero knob which can be locked /sealed.

This meter indicates maximum current drawn by an electrical installation over a period of time. Following are the applications such as:
a)      For electricity board to know whether a premise has exceeded the load sanctioned to him.
b)      In a high rise building, the electrical cabling is done for specified load however over a period of time, the load in the building increases, which when exceeds the specified limit, hits of the cabling.
This is a measure reason of a short circuit and fire in high rise building. If this instrument is installed, it will always indicate to the regulating authorities the maximum current drawn. If it exceeds this specified limit the corrective action can be taken before hand and fire hazards can be prevented.
c)      In a motor control circuit, the use of such instrument will indicate to the company if the operator is continuously overloading the motor.
d)     For a generating set, such instrument will indicate to the supplier company what has been the load on which generating set has been operated. This is very much useful for maintenance.

Active/reactive power meters:
Watt meters/VAR  are used for active /reactive power measurement respectively for different  types of circuit network and nature of load. These meters are of two types-
·         Electronic transducer type
·         Electrodynamometer type

Accuracy classification:
Accuracy classification is as per IS:1248 1983.It is indicated on the scale.

Mounting position
Required Mounting position  is indicate on the scale in accordance with IS 1248 whereby a deviation of +/- 50 from the position is permissible.; positional error(( in addition to the error on the indication ) must not exceed the error appropriate  to the meter classification for frequency.

Movement Symbol
      















5 comments:

  1. Well Explained..
    I mean how sort of things are helpful to get guidance from these electrical engineering instruments. They are really amazing in nature to help us to make our practicals with some ease.
    The foremost thing to share or declare here is from where we can get these kind of Electrical Engineering Lab Testing Instruments-Electrical Engineering Instruments for our experiments.
    Basically Atico Export the well established firm is there to help you in every of your requirement of Scientific Educational Equipments. They are well known Manufacturer, Supplier and Exporters of India.
    So just satisfy your needs to get the most amazing and long-lasting Electrical Engineering Lab Equipment Manufacturer, Supplier and Exporters.

    ReplyDelete
  2. We provide best PLC training in Delhi NCR at affordable course fees with 100% JOB assistance life time. Our Aim is developing employable skills. DIAC is one of the well equipped PLC training institute in Noida. We provide practical training on live project and advanced level PLC training in Noida & Delhi which helps to students in a better understanding. Call @9818293887.

    ReplyDelete
  3. I search many blog about the Apparatus Manufacturers but did not get many specific detail about the this topic but your blog have a lot of information about my topic Engineering Lab Instruments Supplier

    ReplyDelete

  4. Thanks for sharing this Article and here is some information aboutVasthi Instruments

    ReplyDelete
  5. Solar power is empowering individuals to take control of their energy consumption. Solar company

    ReplyDelete

One Nation, One electrical License

Electrical contractors are facing license problem when they bid for another state. Generally they are entitled to do work in particular stat...