Sunday 27 October 2013

Busbar size and calculation


Busbar
Bus bar 

A bus bar (also spelled busbar, buss bar or busbar), is a strip or bar of copper, brass or aluminum that conducts electricity within a switchboard, distribution board, substation, battery bank or other electrical apparatus. Its main purpose is to conduct electricity, not to function as a structural member.
Busbars are typically either flat strips or hollow tubes as these shapes allow heat to dissipate more efficiently due to their high surface area to cross-sectional area ratio. A hollow section has higher stiffness than a solid rod of equivalent current-carrying capacity, which allows a greater span between busbar supports in outdoor switch yards.
A busbar may either be supported on insulators, or else insulation may completely surround it. Busbars are protected from accidental contact either by a metal earthed enclosure or by elevation out of normal reach. Power Neutral busbars may also be insulated. Earth (safety grounding) busbars are typically bare and bolted directly onto any metal chassis of their enclosure. Busbars may be enclosed in a metal housing, in the form of bus duct or busway, segregated-phase bus, or isolated-phase bus.
Busbars may be connected to each other and to electrical apparatus by bolted, clamp, or welded connections. Often joints between high-current bus sections have matching surfaces that are silver-plated to reduce the contact resistance. At extra-high voltages (more than 300 kV) in outdoor buses, corona around the connections becomes a source of radio-frequency interference and power loss, so connection fittings designed for these voltages are used.
Busbars are typically contained inside switchgear, panel boards, or busway. Distribution boards split the electrical supply into separate circuits at one location. Busways, or bus ducts, are long busbars with a protective cover. Rather than branching the main supply at one location, they allow new circuits to branch off anywhere along the route of the busway.
Advantages
 Following are some advantages of Bus bar trunking system over normal cabling system:-
1.      On-site installation times are reduced compared to hard-wired systems, thus leading to cost savings.
2.      It provides increased flexibility in design and versatility with regard to future modifications.
3.      Greater safety and peace of mind for specifiers, contractors and end-users.
4.      Because of the simplicity of busbar, it is easy to estimate costs from the design/estimating stage through to installation on site.  This is because the technical characteristics and price of each component are always known.
5.      It is short sighted to compare the cost of busbar against that of a length of cable — and not the real cost of a cable installation to include multiple runs of cable, tray and fixing, let alone the protracted time and effort of pulling cables.
6.      Distribution busbar distributes power along its length through tap-off points along the busbar at typically at 0.5 or 1 m centers. Tap-off units are plugged in along the length of the busbar to supply a load; this could be a sub distribution board or, in a factory, to individual machines. Tap-offs can normally be added or removed with busbar live, eliminating production down time.
7.      Installed vertically the same systems can be used for rising-mains applications, with tap-offs feeding individual floors. Certified fire barriers are available at points where the busbar passes through a floor slab. Protection devices such as fuses, switchfuses or circuit breakers are located along the busbar run, reducing the need for large distribution boards and the large quantities of distribution cables running to and from installed equipment.
8.      Very compact so provides space savings.
9.      Where aesthetics have to be considered, busbar trunking can be installed with natural galvanized, aluminium, or painted finish. Special colours to match switchboards or a specific colour scheme are also available on request.
10.  Busbar trunking has several key advantages over conventional forms of power distribution including: -
11.  (a) Reduced, onsite installation times when compared to hard-wired systems thus leading to cost savings.
a.        Increased flexibility in design and versatility with regard to future modifications.
b.       Increased safety features brought about by the use of high quality, manufactured components, which provide greater safety and peace of mind for specifies, contractors and end-users.
12.  Uneven distribution of current takes place where multiple runs of cables are used in parallel.
13.  Busbar trunking has tap-off points at regular intervals along each length to allow power to be taken off and distributed to where it is needed. Because it is fully self-contained it needs only to be mechanically mounted and electrically connected to be operational.
14.  For higher ratings of power distribution we need to have multiple runs of cable. In such conditions unbalanced distribution of current takes place and causing overheating of some cable. This is completely avoided in the BTS systems.
15.  When multiple runs of cables are used it often leads to improper end connections thereby causing overheating of contacts, burning of cables ends, and is a major cause of fire. This is completely avoided in Bus Bar Trunking systems.
Current carrying capacity
The current-carrying capacity of a busbar is usually determined by the maximum temperature at which the bar is permitted to operate, as defined by national and international standards such as British Standard BS 159, American Standard ANSI C37.20, etc. These standards give maximum temperature rises as well as maximum ambient temperatures.
BS 159 stipulates a maximum temperature rise of 50°C above a 24 hour mean ambient temperature of up to 35°C, and a peak ambient temperature of 40°C.
ANSI C37.20 alternatively permits a temperature rise of 65°C above a maximum ambient of 40°C, provided that silver-plated (or acceptable alternative) bolted terminations are used. If not, a temperature rise of 30°C is allowed.
A very approximate method of estimating the current carrying capacity of a copper busbar is to assume a current density of 2 A/mm2 (1250 A/in2) in still air. This method should only be used to estimate a likely size of busbar, the final size being chosen after consideration has been given to the calculation methods. Refer catalogue of manufacturers.
The more popular thumb rule being followed in India is to assume current density of 1.0 Amps / Sq.mm for Aluminium and 1.6 Amps for Copper for any standard rectangular conductor profile.
Standard size of bus bar
Sr.
Application area
Cable
busbar
1
Number of circuits
One circuit per floor. Hence for a 20-floor building, you need 20 circuits.
Just one circuit can cover all floors.
2
Main Switchboard
Need 1 outgoing for each circuit. Hence 20 nos. MCCB outgoings. Higher cost and larger space requirement in electrical room
Need only 1 outgoing for each riser. Lower cost and size of main panel.
3
Shaft Size
Using 4 core cables, and considering 1 cable per feeder, you need 20 cables on the lowest floor. Large space required for cables/ cable tray.
Typical size of 1600A riser is 185mm x 180mm. Leads to big savings on riser shaft size, and hence more usable floor area on every floor.
4
Fire & safety
The high concentration of insulating materials used in cables and conductors involves a very high level of combustive energy.
The volume of insulating materials used in trunking is reduced to a minimum so combustive energy is considerably lower than cables. The insulating materials used do not release corrosive or toxic gases in the event of a fire. Once the source of the fire is removed, these materials are extinguished in a few seconds so that the effect of the fire is minimised
5
Future expansion
load on any floor exceeds initial plan, owner has to run an additional cable from a spare feeder on main board to that floor.
By providing extra tap off slots on each floor at the design stage, owner only has to procure a tap off box and plug it in wherever additional load is required. As the plug in can be done live, there is no shut down required for any of the existing clients / circuits. Future Flexibility.
6
Fault withstand levels
Limited by conductor size of each circuit.
Much higher – typically a 1600 A riser has a fault withstand capability of 60 to 70 kA. Safer in an electrical fault.
7
Installation time
Much longer
Each riser on a 20-floor building can be installed in approximately 2 to 3 days.
8
Voltage drop
High impedance if you choose cable size based on each floor current rating.
Much lower impedance. Hence substantially lower voltage drop.

Busbars Reduce System Costs
A laminated busbar will lower manufacturing costs by decreasing assembly time as well as internal material handling costs. Various conductors are terminated at customer specified locations to eliminate the guesswork usually associated with assembly operating procedures. A reduced parts count will reduce ordering, material handling and inventory costs.
 Bus bars Improve Reliability
 Laminated bus bars can help your organization build quality into processes. The reduction of wiring errors results in fewer reworks, lower service costs and lower quality costs.
Bus bars Increase Capacitance
 Increased capacitance results in decreasing characteristic impedance. This will ultimately lead to greater effective signal suppression and noise elimination. Keeping the dielectrics thin and using dielectrics with a high relative K factor will increase capacitance.
Eliminate Wiring Errors
By replacing a standard cable harnesses with bus bars, the possibility for miss-wirings is eliminated. Wiring harnesses have high failure rates relative to bus bars, which have virtually none. These problems are very costly to repair. Adding bus bars to your systems is effective insurance.
Bus bars Lower Inductance
 Any conductor carrying current will develop an electromagnetic field. The use of thin parallel conductors with a thin dielectric laminated together minimizes the effect of inductance on electrical circuits. Magnetic flux cancellation is maximized when opposing potentials are laminated together. Laminated bus bars have been designed to reduce the proximity effect in many semiconductor applications as well as applications that involve high electromagnetic interference (EMI).
Bus bars Lower Impedance
 Increasing the capacitance and reducing the inductance is a determining factor in eliminating noise. Keeping the dielectric thickness to a minimum will accomplish the highly desired low impedance.
Bus bars Provide Denser Packaging
 The use of wide, thin conductors laminated together led to decreased space requirements. Laminated bus bars have helped decrease total system size and cost.
Bus bars Provide Wider Variety of Interconnection Methods
 The flexibility of bus bars has allowed an unlimited number of interconnection styles to choose from. Bushings, embossments, and fasten tabs are most commonly used.
Bus bars Improve Thermal Characteristics
 The wide, thin conductors are favourable to allowing better airflow in systems. As package sizes decrease, the cost of removing heat from systems has greatly increased. A bus bar cannot only reduce the overall size required, but it can also improve airflow with its sleek design.
Material: The copper will be of ETP grade as per DIN 13601-2002 and with oxygen free copper.
Chemical composition: Purity of copper will be as per DIN EN 13601:2002. Copper + Silver 99.90% min.
Typical example
Rating Current: 3200Amp.
System:415Vac, TPN, 50Hz.
Fault Level: 50KA. For 1 Sec.
Operation Temp:40° C rise over 45 ° C ambient.

CONSIDERATION
Enclosure size: 1400 mm. wide X 400mm. height
Bus bar Size: 2:200x10 per Ph., 1:200x10 for Neutral.
Bus bar material: Electrolytic gr. Al. (IS 63401/AA6101)

 Short Circuit Rating
-upto 400A rated current:                   25KA for 1 sec.
-600 to 1000A rated current:              50KA for 1 sec.
-1250 to 2000A rated current:            65-100KA for 1 sec.
-2500 to 5000A rated current:            100-225KA for 1 sec.

The minimum cross section needed in sqmm for busbar in various common cases can be listed as below-

Material
Fault level (KA)
Withstand time


1 sec.
200 msec.
40 ms.
10 ms.

Aluminium
35
443
198
89
44
50
633
283
127
63
65
823
368
165
82







Copper
35
285
127
57
28
50
407
182
81
41
65
528
236
106
53


Let us select a busbar with an example:
1)  Aluminium busbar for 2000A, 35 kA for 1 sec withstand – From the table the minimum cross-section needed would be 443 mm2. Thus we can select a 100mm x 5mm busbar as the minimum cross-section. Considering a current density of 1A/ mm2 by considering temperature  as well as skin effect, we shall require 4 x 100mm x 5mm busbars for this case.

2)  Copper busbar for 2000A, 35 kA for 1 sec withstand – From the table the minimum cross-section needed would be 285 mm2. Thus we can select a 60mm x 5mm busbar as the minimum cross-section. Considering a current density of 1.6A/ mm2 by considering temperature as well as skin effect, we shall require 4 x 60mm x 5mm busbars for this case.

 Thus, by using the above formula and table, we can easily select busbars for our switchboards.
Size in mm
Area sqmm
Weight/ km
current carrying capacity in amp ( copper ) at 35 deg.C
AC ( no. of bus)
DC ( no. of bus)
I
II
III
II II
I
II
III
II II
12X2
24
0.209
110
200


115
205


15X2
30
0.262
140
200


145
245


15X3
75
0.396
170
300


175
305


20X2
40
0.351
185
315


190
325


20X3
60
0.529
220
380


225
390


20X5
100
0.882
295
500


300
510


25X3
75
0.663
270
460


275
470


25X5
125
1.11
350
600


355
610


30X3
90
0.796
315
540


320
560


30X5
150
1.33
400
700


410
720


40X3
120
1.06
420
710


430
740


40X5
200
1.77
520
900


530
930


40X10
400
3.55
760
1350
1850
2500
770
1400
2000

50X5
250
2.22
630
1100
1650
2100
650
1150
1750

50X10
500
4.44
920
1600
2250
3000
960
1700
2500

60X5
300
2.66
760
1250
1760
2400
780
1300
1900
2500
60X10
600
5.33
1060
1900
2600
3500
1100
2000
2800
3600
80X5
400
3.55
970
1700
2300
3000
1000
1800
2500
3200
80X10
800
7.11
1380
2300
3100
4200
1450
2600
3700
4800
100X5
500
4.44
1200
2050
2850
3500
1250
2250
3150
4050
100X10
1000
8.89
1700
2800
3650
5000
1800
3200
4500
5800
120X10
1200
10.7
2000
3100
4100
5700
2150
3700
5200
6700
160X10
1600
14.2
2500
3900
5300
7300
2800
4800
6900
9000
200X10
2000
17.8
3000
4750
6350
8800
3400
6000
8500
10000

Temperature rise

During the short circuiting, the bus bar should be able to withstand the thermal as well as mechanical stress. When a sort circuiting takes place, the temperature rise is directly proportional to the squire of the rms value of the fault current. The duration of short circuiting is very small i.e. one second till the breakers opens and clears the fault. The heat dissipation through convection and radiation during this short duration is negligible and all the heat is observed by the busbar itself. The temperature rise due to the fault can be calculated by applying the formulae.

T = K (I/A) 2 (1+αθ) 10-2
T=temperature rise per second
A= conductor cross section area
α = temperature coefficient of resistivity at 20 deg.C/deg.C
   = 0 .00393 for copper
   = 0 .00386 for aluminium
K = constant
    =0.52 for copper
    =1.166 for aluminium
θ = temperature of the conductor at the instant at which the temperature rise is being calculated.

Typical calculation

Rated current = 1000A
Fault current = 50KA for 1 sec
Permissible temperature rise= 40 deg.C
Busbar material =aluminium ally E91E
De-rating factor due to material =1
De-rating factor due to temperature rise =0.86
De-rating factor due to enclosure =0.75
Total de-rating factor = 1x0.75x0.86=0.66
Minimum cross section area required to withstand short circuit for 1 sec.
                  = (Ifc xt )/0.08
Where, Ifc = fault level current in KA
                 t= 1 second
Area A = (50x√1 )/0.08 = 625 sqmm
 Considering all de-rating factor, A = 625/0.66 =946.97
Say, cross sectional area per phase = 1000 sqmm
For neutral, cross sectional area per phase = 500 sqmm


for more study -refer a practical guide to cable installation and tool box talk
In India -

Available with book shop and -


Price: Rs. 375/- excluding delivery charges




137 comments:

  1. main switchboards
    is a specialist Switchboard Manufacturing company incorporated in 1973.We have established a leading reputation for the design and delivery of high quality,cost effective switchboard.

    ReplyDelete
  2. Reader can see more information on
    http://www.sanjaytechnical.in/11kv-bus-duct/11kv-bus-duct.html

    ReplyDelete
    Replies
    1. How to select BUS BAR for chiller control panel when chiller takes 352 AMPS,400V, 50KA

      Delete
    2. 40 X 6 MM COPPER BUSBAR CAN HOLD 50KA FOR 0.25 SEC WITH RUNNING BUSBAR CAPACITY OF 415 AMPS

      Delete
  3. Under Typical Calculation,How do you have taken 0.08 value,please confirm?

    ReplyDelete
  4. How to calculate bus bar current

    ReplyDelete
    Replies
    1. IF BUSBAR IS OF 40X6 MM
      SO 40X6=240
      CONDUCTIVITY OF COPPER=1.6 A/MM2
      CONDUCTIVITY OF ALUMMINIUM=0.8 A/MM2

      SO IF COPPER BUSBAR = 240 X 1.6 =384 AMPERE
      ALUMINIUM BUSBAR= 240 X 0.8=192 AMPERE

      Delete
  5. How to calculate bus bar current

    ReplyDelete
    Replies
    1. Anonymous23 December 2017 at 01:31
      IF BUSBAR IS OF 40X6 MM
      SO 40X6=240
      CONDUCTIVITY OF COPPER=1.6 A/MM2
      CONDUCTIVITY OF ALUMMINIUM=0.8 A/MM2

      SO IF COPPER BUSBAR = 240 X 1.6 =384 AMPERE
      ALUMINIUM BUSBAR= 240 X 0.8=192 AMPERE

      Delete
    2. i confused once match with the selection chart above give for busbar selection. As per chart OF COPPER 40X5 is giving 900A Load but as per your calculation it is coming 384Amp Only. can you please elaborate

      Delete
  6. This comment has been removed by a blog administrator.

    ReplyDelete
  7. which bus bar is better? Having current density 1.2 or 1.6

    ReplyDelete
    Replies
    1. SURELY 1.6, SO CURRENT FLOWING THROUGH MM2 OF BUSBAR IS MORE

      Delete
  8. Calculate your BMI by using our Body mass index Calculator for adults & children. Calculated by dividing the weight in kilograms by the square of height in meters. Weight Calculator

    ReplyDelete
  9. This comment has been removed by a blog administrator.

    ReplyDelete

  10. As per my requirement, I am searching Bus Bar Cross Section (Thickness & Width) for 3A, 5A, 10A, 30A, 40A, 100A, 250A Current rating.

    ----------------------------------------
    Thanks With Best Regards,
    | Ankur Afre. | Mob. No : 91 - 9421511797 | Desk No : 91-2066209365
    | Mail. : ankur.afre@hindujatech.com |

    ReplyDelete
  11. Amazing site, Distinguished criticism that I can handle. Im advancing and may apply to my present place of employment as a pet sitter, which is exceptionally agreeable, yet I have to extra grow. Respects. camping generators

    ReplyDelete
  12. if i have a load 500 kva and 800 kva both have feed from (far 50m and 150m from panel resp.)transformer panel, how can calculate the specified bus duct (only one bus duct for both),also can we devide main bus duct into two branches with two different rates for two loads?

    ReplyDelete
  13. = (Ifc x√t )/0.08

    what is 0.08? how did u calculated it ? please explain

    ReplyDelete
  14. what is the current of 25x3mm copper bus bar

    ReplyDelete
  15. i design the panel and current rating is 400amp so which size of busbar i used

    ReplyDelete
    Replies
    1. Use this calculation for selection of busbar

      Ampacity=Width*Thk*1.55

      So in your case 40*8*1.55=496 Amp
      or 35*8*1.55= 434 Amp

      Delete
    2. which book do u referring using 1.55?

      Delete
  16. if we have 3*450 MVA and 1*750 MVA transformer for 500 kv Subsation with one and half breaker scheme what should be the rating of the bus bars

    ReplyDelete
  17. Great blog ! I really like your blog. Your blog is very informative. Thanks for sharing such a useful blog. Paraflex is leading Best Top Aluminium Wire Manufacturers in India in India, certified by BIS, ISO, NSIC, SSI. We provide you housing wire, industrial wire , aluminium cable, cctv cable etc. of best quality and all cables are available at the best price.

    ReplyDelete
  18. I want design a panel for 3200ampere current on incomer so how should i decide my busbar size for aluminium as wess as copper?

    ReplyDelete
  19. Generally we are using cable aluminium. Aluminium is available everywhere. you can select from chart. from chart 80 X 10 x4 nos. bus may be sufficient for your requirement but consider other parameter like temperature, safety factor etc

    ReplyDelete
  20. Great post. Know the power of steel, These plates are manufactured by the vendors using superior grade mild steel so as to ensure their longer service life and high tensile strength. ms plate price in Chennai will offer you an affordable price.

    ReplyDelete
  21. This comment has been removed by a blog administrator.

    ReplyDelete
  22. I want design a panel for 18000A current on main-bus copper so how should i decide my bus-bar size and no of run (we Required maximum no of Run 4)?
    and Outgoing 6300A (we Required maximum no of Run 2). bus bar Copper.

    ReplyDelete
    Replies
    1. Let's take busbar c/s = 250x25mm
      Number runs can have = 2Runs
      Current density of copper = 1.6Amps/mm2

      Calculate: 250x25x2x1.6 = 20000Amps

      Delete
  23. you can see more detail in book" A practical guide to cable installation and tool box talk"'

    ReplyDelete
  24. Hello Sir,
    I want to select busbar for HT panel . Calculated regular load 800 Amp.
    Supply voltage 11000v.
    So which busbar is suitable for the this HT panel i.e. Al. Or Cu.

    And how , what calculation are considered and also consider the fault current if fault occurs at site.

    Sir please reply with all calculations and consideration means it will clear to me to explain

    Sir You can also mail me on

    Kiran.bhalsinge@gmail.com

    ReplyDelete
  25. The article above provides a tabulation for selection of different busbar sizes for switchboard. The heading on the table states "current carrying capacity in amp ( copper ) at 35 deg.C". Can you please clarify if the specified 35 deg.C is the ambient temperature value or the temperature rise of the busbar? If the 35 deg C is the temperature rise value, then what is the ambient temperature that is applicable for the values given in the tabulation? Also what would be the applicable derating factors for different temperature rise values? Your feedback is greatly appreciated. Thank you. Hardeep Singh. hsujagar@gmail.com

    ReplyDelete
  26. how to calculate current capacity for the 1mmx5mm copper strip?

    ReplyDelete
    Replies
    1. for detail: "a practical guide to cable installation and toolbox talk".

      regards
      amieclub@gmail.com team

      Delete
  27. I really appreciate this particular blog and exactly how its laid out, thankyou I’ve saved.Air conditioning companies near me

    ReplyDelete
  28. Good day Sir, just want to ask if do we base the busbar size based from the demand load or based from the rating of the main circuit breaker? thank you.

    ReplyDelete
  29. Replies
    1. it is haram for a muslim to practice your so called craft. a load of hogwash

      Delete
  30. Евроокна из цельноламельной лиственницы со стеклопакетом в брусовом доме Для загородного коттеджа были произведены и установлены деревянные окна из древесины лиственницы со стеклопакетами. Брус: трехслойный клееный, цельноламельная лиственница, сорт АЕ. Отделка: покрытия на водной основе «RENNER Aquaris», Италия. Цвет отделки - Махагон. Стеклопакеты: двухкамерные энергосберегающие с низкоэмиссионым И-стеклом. На большом глухом окне выполнена расстекловка бруском толщиной 50 мм. Окна под крышей на 3 этаже имеют фальшпереплеты внутри стеклопакета толщиной 18 мм. Больше информации

    ReplyDelete
  31. Hello, I like to use Copper bus bar for single one (Earthing) form LT panel to 08 stories building Top instead of individual Earthing cable . Is it feasible or not, please help any person. Size 50 X 10 mm.

    ReplyDelete
  32. Nice blog, really informative, keep sharing such blogs. High quality Multi Switch Outlet Power Strips supplier offers electrical outlet power strips, ac outlet strips, electric plug strips and hardwired power strips with USB. Visit our website and find yours.
    power strips with usb

    ReplyDelete
  33. Thank you for sharing the valuable content.

    The electrical test and measurement range of products from Josts’ Electrical Division ensures performance and reliability in power generation, transmission and distribution equipments. Josts has rich experience of over eight decades in providing advanced technology products and systems dedicated to various applications in Electrical Industry. Josts has pioneered many concepts in electrical testing and measurement for various applications in India such as Insulation Testing,

    electrical testing and measurement
    material handling
    Cable Fault Locators

    ReplyDelete
  34. DEAR SIR WE ARE MANUFACTURING COPPER PRODUCTS ANY TYPE ALL SIZE BUS BARS WIRE AND RODS FLAT
    REGARDS
    CUBEX TUBINGS LTD
    PATANCHERU
    HYDERABAD
    TELANGANA
    INDIAN 502319
    8555945185
    CUBEX@REDIFFMAIL.COM
    CUBEXMOHAN@GMAIL.COM

    ReplyDelete
  35. https://electricalnotes.wordpress.com/2014/08/05/panel-design-calculate-size-of-bus-bar/

    ReplyDelete
  36. This comment has been removed by a blog administrator.

    ReplyDelete
  37. Thank you for sharing the valuable content.Jost’s material handling provides innovative solutions for internal material handling needs for its customers so that it improves the efficiencies of their processes.
    Constant Temperature Anemometry
    Cable Fault Locators

    ReplyDelete
  38. Hi there,

    Thank you so much for the post you do and also I like your post, Are you looking for Buy Buspirone Online without prescription in UAE? We Buy Buspirone Online without prescription , health bio-pharma online pharmacy, online pharmacy In Saudi Arabia, Buy Pills Online, High Rated Pills for Sale, Online Pharmacy Near you, Abortion Pills in Offer, Abortion pills Cytotec available in Dubai, Abortion Pills Cytotec available in Dubai, discount e pharmacy online in Riyadh, online e-pharmacy market In Bahrain, online pharmacy help Saudi Arabia, online pharmacy hub In Saudi Arabia, online pharmacy near me, online pharmacy stock, how to get online doctors prescriptions, anxiety pills prescribed, Is miferpristone and misoprostel available in UAE, Cytotec medicine in UAE,How to get abortion pills in UAE, Where to buy cytotec in Dubai, , Dubai online shopping tablets, Mifegest kit price online order, Vimax pills in Dubai, Cytotec 200 Mcg in Riffa, Cytotec 200 Mcg in , Misoprostol in Dubai pharmacy what are good anxiety pills, anxiety pills buy online in Saudi Arabia, anxiety pills best in Kuwait, for you with the well price and our services are very fast.
    Click here for href="https://onlineplanpharmacist.com/product/buy-buspirone-online-with-prescription/" />title" Buy Buspirone Online Without Prescription |Buy Pills Online| High rated pills for sale| Online Pharmacy Near You" />MORE DETAILS......

    Contact Us: +1 (443) 718-9645
    Email Us At: support@healthsbiopharma.com

    ReplyDelete
  39. This comment has been removed by a blog administrator.

    ReplyDelete
  40. This comment has been removed by a blog administrator.

    ReplyDelete
  41. Hi there,

    Thank you so much for the post you do and also I like your post, Are you looking for for Buy Abortion Pills Online in UAE? We Buy Abortion Pills Online, Misoprostol in Dubai pharmacy, Abortion pills for sale in Dubai, Where i can buy abortion pills in Abu Dhabi, Abortion pills price in Dubai, Abortion pills for sale in Ajman, Where i can buy abortion pills in Dubai, Where i can buy abortion pills in Sharjah, Buy Mifepristone and misoprostol online UAE, Abortion pills cytotec available in Dubai, Buy abortion pills in Dubai, Cytotec pills in Dubai, Cytotec price in Dubai, Cytotec pills in Dubai, Cytotec price in Dubai, Abortion pills in Dubai, mifegest kit in UAE, Pregnancy termination pills in Qatar, Abortion in Dubai, pregnancy abortion pills in UAE, Mifepristone and misoprostol available in UAE, Cytotec medicine in UAE, How to get abortion pills in UAE, Abortion pills available in Dubai, Where to buy cytotec in Dubai, Abortion pills in Qatar pharmacy, Dubai online shopping tablets, Abortion clinics in muscat, Where to buy abortion pills in Bahrain, Abortion pills in Ajman, Mifegest kit price online order, Vimax pills in Abu Dhabi, Where can i buy mifepristone and misoprostol in Dubai, Can you take birth control pills in Dubai, Abortion pills in UAE for sale,the well price and our services are very fast.
    Click here for " title="Buy Abortion Pills online | Misoprostol in Dubai Pharmacy | Abortion in Dubai | Abortion Pills in Dubai"/>MORE DETAILS......

    CONTACT US:
    Phone : +1 (443) 718-9645
    support@healthsbiopharma.com

    ReplyDelete
  42. This comment has been removed by the author.

    ReplyDelete
  43. You have made valid points in a unique way. Since this has made me think, I will have to review some aspects.
    Since 2009, Electrical Services Company, Positive Contractors, is providing both commercial & domestic Electrical Services Electrical Contractors in London emergency electrician London

    ReplyDelete
  44. WPS Round Bar Supplier in Ahmedabad
    Gokul Steel is leading supplier of WPS Flat Bar and Round Bar Supplier in Ahmedabad. We also supplier of D-2,D-3, En-31, H-11, H-13, P-20,Flat Bar, Round Bar, Mild Steel Square Bar and etc.

    ReplyDelete
  45. topic is covered in book and available in market -a practical guide to cable installation and tool box talk.

    ReplyDelete
  46. This drug test is used by businesses and law enforcement, and it is extremely successful at identifying drug traces when compared to blood and urine samples. Before getting results from a hair follicle drug test, a chunk or even a single hair (typically from the root or follicle) must be sent to a laboratory overnight. Drug residues can commonly be found in a person's hair for up to three months. This happens because a hair follicle's blood vessels are in constant touch with the bloodstream, allowing toxins to accumulate. When going to the sauna, whether to detox for drug tests or any other reason, it's important to stay hydrated and drink lots of water. In just a short amount of time, you could lose a significant amount of sweat and increase your risk of dehydration. Visit: https://www.urineworld.com/

    ReplyDelete
  47. Your content is full of respectable information that is usable for today's readers. I have very much enjoyed this informational content. Your layout is excellent. I will come back again. We Can print any size of Round Stickers and Labels. best Sticker printers for 1 inch size, 2 inch size 4 Inch round labels. Call NOw....

    ReplyDelete
  48. Gain the essential skills to recruit, develop and manage an organisation's most valuable asset - its people.Studying Human resource management at IIM, Calcutta turns you into a strategic player who knows how to position employees for the long-term success of a company.Our Masters programmes feature a mix of core and optional modules, tailoring your degree towards various industry elements of human resource management practice.We'll teach you how to achieve the best results from employees through practical workshops, where you'll apply human resource management practices to address real situations in the workplace.You'll be studying with the School of Management—a leading management school in India with an international reputation for high-quality scholarship.

    ReplyDelete
  49. Electricians in my area


    NO CALL OUT CHARGE Grip Electric Limited has a team of experts engineers offering emergency electricians near me 24 hours.Contact us on 02034881842 and get our assistance! gripelectric.net Emergency Electrician near me NO CALL OUT CHARGE Local Emergency Electrician near me

    ReplyDelete
  50. I want to know the calculation formula of DC current(A) on 8mm×71mm(copper),Thank.

    ReplyDelete
  51. Plastic Pulverizer in Gujarat
    Plastic Pulverizer in Gujarat. Moreover, we can offer the products as per the specifications by customers to their exact requirements.

    ReplyDelete
  52. Aluminum Storage Tank in India
    Aluminum Storage Tank in India. Aluminum Vertical Storage Tank Avaibility : in stock Category: Storage Tanks

    ReplyDelete
  53. High Speed Cooler Heater Mixer in India
    High Speed Cooler Heater Mixer in India. Acid Storage Tank Avaibility : in stock Category: Storage Tanks Approx. Rs 1.8 Lakh / Unit

    ReplyDelete
  54. Wao thats great brother very awesome content I have also write something about that
    yoga mat thickness chart

    ReplyDelete
  55. I like your all post. You have done really good work. Thank you for the information you provide, it helped me a lot. I hope to have many more entries or so from you.
    Very interesting blog.
    vstkey.com
    Maxon CINEMA 4D Studio Crack
    Overloud TH-U Full Crack
    Mirillis Action Crack
    plugin alliance all bundle Crack

    ReplyDelete
  56. I guess I am the only one who came here to share my very own experience. Guess what!? I am using my laptop for almost the past 2 years, but I had no idea of solving some basic issues. I do not know how to Download All Crack Software's For Free Here But thankfully, I recently visited a website named Crackroom
    8 Ball Pool Crack

    ReplyDelete
  57. Every business should have a good UPS battery backup so that the company's data and other material is protected.
    Thanks
    Apple Dubai, UAE
    UPS Suppliers in Dubai, UAE
    Ubiquiti Suppliers & Wholesalers in Dubai, UAE


    ReplyDelete
  58. This comment has been removed by the author.

    ReplyDelete
  59. When you see a problem or realize that your home needs electrical maintenance, it is critical to contact a trained and highly skilled electrical contractors reading. Only an electrician is licensed and has the necessary experience to provide electrical services while adhering to all regulations and standards.
    emergency electrician reading

    ReplyDelete
  60. This comment has been removed by the author.

    ReplyDelete
  61. When I felt like giving up completely, Dr Ilekhojie stepped in and reminded me that nothing is too hard for Him! I have been standing for many years and didn’t know that I was on the verge of accepting to divorce my husband, when I found Dr Ilekhojies contact online. It took me getting to a place of being absolutely broken for me to see that I needed to tell him what i had been facing in my marriage with my husband. I made a War Room in my bedroom closet and went straight to the Source! It did get hard many times; my husband was still at home and not being supportive and still wanted a divorce, but I knew the little i had would sustain me and my daughter.Then suddenly came this past Saturday, Dr Ilekhojies reconciliation spell put him in a place to decide whether he would abandon us or work on our marriage. Only by the reconciliation spell spell did he actually say that he still wanted to be married and canceled the contract on a home he was about to buy in Hemet California! Indeed, nothing is impossible with Dr Ilekhojies reconciliation spell. NEVER give up!” contact Dr Ilekhojie if you are having problems in your marriage or relationship on gethelp05@gmail.com or reach out with his phone number +2348147400259

    ReplyDelete
  62. I felt very happy while reading this site. This was really very informative site for me. I really liked it. This was really a cordial post. Thanks a lot!. control panel manufacturers in india

    ReplyDelete
  63. What a great article, thank you for writing and sharing with us. Buy MTP Kit Online

    ReplyDelete
  64. 흥덕구출장샵
    상당구출장샵
    장안구출장샵
    권선구출장샵
    수지구출장샵
    시흥구출장샵
    Hi there! I just want to offer you a huge thumbs up for the great information you have here on this post. I’ll be coming back to your website for more soon.

    ReplyDelete
  65. Thanks for sharing this informative post!
    for Unwanted pregnancy problem Buy Mtp Kit Online from mysafepillsrx pharmacy.

    ReplyDelete
  66. If you want to know about pregnancy test kits manufacturer in India, Alpine Biomedicals in of the best Pregnancy Test Kit Manufacturers in India that provides high-quality test kits which are easy to use and easy to portable. The company gained fame as the top Urine Pregnancy Test Kit Manufacturers in India.

    ReplyDelete
  67. Thanks for sharing this information. To know more click on Manufacturer of Copper U-Bend in bangladesh

    ReplyDelete
  68. Good article for all mechanical engineering students to read and learn from. Do check our article of learn web development! Thanks.

    ReplyDelete
  69. I really enjoyed your blog Thanks for sharing such an informative post.House Shifting Service in Islamabad

    ReplyDelete
  70. Due to our extensive selection of SMTP server for Gmail, you are not need to come to Digitalaka for the setup of your whole email marketing strategy. Let us know what you need, and we'll work with you to create, carry out, and monitor your email marketing strategy as soon as possible.

    ReplyDelete
  71. Ecommerce company has its own unique challenges when it comes to software integration, with multiple sales platforms, payment service provider (PSP) and inventory apps to contend with.

    ReplyDelete
  72. Hey, Are looking for an agency that provides property management Related Services in the united. DPI Web offers the Best Provide service Which is DPI Property Management. In this Service, they manage your all Real Estate Property.

    ReplyDelete
  73. Hey Nice blog, Are you want to promote this by
    email marketing mumbai agency in mumbai

    ReplyDelete
  74. This is a very nice article to read, I have bookmarked your website
    bulk email marketing in mumbai

    ReplyDelete
  75. what is 0.08 in that formula and from where you have taken

    ReplyDelete
  76. Originally used for floor marking, vinyl floor stickers have developed into a variety of uses. From health and safety messages to advertising new products, these are a great way to communicate with customers. They used as a tool for displaying special areas, showcasing specific pallets, or identifying shelving contents. For more information visit here: Using Vinyl Floor Stickers in a Variety of Ways

    ReplyDelete
  77. very happy to read this article . would love to read it again smtp relay for bitcoin

    Powermta donwload

    ReplyDelete
  78. Thanks for sharing this wonderful information. To know more click on rectangular copper tube

    ReplyDelete

  79. I'm reading your complete blog, it is really impressive and helpful content!
    Business Listing all about Rajshri Mobile Cables Online in Dubai at the best price with wholesale only. Select one of the best USB Data Cables in 2023. Shop Now. I'm reading your complete blog, it is really impressive and helpful content!
    Business Listing all about Rajshri Mobile Cables Online in Dubai at the best price with wholesale only. Select one of the best USB Data Cables in 2023. Shop Now.






    ReplyDelete
  80. Thanks for sharing this information. To know more click on 90/10 Cupro Nickel Rods

    ReplyDelete
  81. Find great deals on the latest styles of led power supplies. Shop online for LED Power Supply from a wide selection of brands, like Mean Well and more at Signprotrading.

    ReplyDelete
  82. Thank you for sharing this information. I observed it very informative and helpful, and I believe you should continue posting articles like this one with useful content.
    software development center in chennai

    ReplyDelete
  83. I have a hard time describing my thoughts on content, but I really felt I should here.Your article is really great.I like the way you wrote this information. home furniture price bd

    ReplyDelete
  84. Dinstar FXO VoIP gateway is a device that allows you to connect traditional analog phone lines (FXO ports) to a VoIP (Voice over IP) network. It acts as a bridge between the traditional phone lines and the digital network, allowing users to make and receive calls over the internet.

    ReplyDelete
  85. Thank you for sharing a wonderful information. Many students struggle to identify a topic that is both interesting and feasible for their dissertation. Dissertation Help providers can assist students in narrowing down their research interests and selecting a topic that is appropriate for their level of study. Overall, dissertation help providers can offer valuable support to students who are working on their dissertation, helping them to complete a high-quality research project that contributes to the body of knowledge in their field.

    ReplyDelete
  86. very informative blog,
    Betterhelpe provides innovative solutions to businesses in Riyadh looking to succeed in today's dynamic marketplace. Contact us today.

    ReplyDelete
  87. This comment has been removed by the author.

    ReplyDelete
  88. Good to explain, Thanks for sharing valuable info. BSD Prime Services and other VAT consultants in Dubai can provide valuable support to businesses of all sizes and industries, helping them to achieve their financial goals and thrive in the challenging business environment of the UAE.

    ReplyDelete
  89. This comment has been removed by a blog administrator.

    ReplyDelete
  90. This comment has been removed by a blog administrator.

    ReplyDelete
  91. Integrated Risk Management is a strategic approach to risk management that aims to unify and streamline the management of various types of risks faced by an organization. IRM integrates different aspects of risk management, including financial, operational, strategic, and compliance risks, into a cohesive framework.

    ReplyDelete
  92. Thanks for sharing this information.

    ReplyDelete
  93. This comment has been removed by the author.

    ReplyDelete
  94. Your article has piqued my interest; however, there are certain aspects discussed within it that I perceive differently. Your valuable insights are sincerely appreciated. As an individual who has encountered challenges while composing assignments for accounting, I discovered that seeking Accounting Assignment Help from proficient experts proved remarkably beneficial for my academic journey.

    ReplyDelete
  95. Preetidevelopers is the leading well-known name in the Real Estate field for developing projects with modern amenities. Visit our website for Villa Developers in Bangalore, Rental Guarantee Villa in Bangalore, and Eco Friendly Homes for Sale in Bangalore.
    Rental Guarantee Villa in Banglore

    ReplyDelete
  96. Welcome to Digital Murgi, your go-to destination for digital marketing and blogging.

    ReplyDelete
  97. This comment has been removed by the author.

    ReplyDelete
  98. Great Work...!!
    Your Post contains valuable content. Thanks for sharing busbar-related information.
    Busbar Machines
    CNC Busway Machine

    ReplyDelete
  99. Great Blog! "Online assignment help has been a game-changer for me. The convenience and quality of assistance are remarkable. I'm grateful to have discovered this reliable support!

    ReplyDelete
  100. Nice Blog! Nursing assignments can be quite challenging, but nursing assignment help services make a real difference. These insights are invaluable for nursing students seeking academic support.

    ReplyDelete
  101. Assignment Help professionalism and expertise shine through every project.

    ReplyDelete
  102. Nice Blog! Nursing education is challenging, and assignments can be overwhelming. That's where nursing assignment help shines. With expert guidance and timely submissions these services offer crucial support. As a nursing student they've been a game-changer providing tailored solutions and easing the academic load. The assistance goes beyond assignments acting as a learning aid for practical applications. For anyone in nursing these services are a lifeline contributing to success in a demanding field.

    ReplyDelete
  103. I have made some document about how to calculate or find bus bar size by using K2 curve with Din table , how can I post to this web blog

    ReplyDelete
  104. The weekly research conducted on "Lloyd's Casualty Reports" was identified as the main reservoir of accident-related data. Although these reports do not expressly mention the causes of accidents, they meticulously outline the progression of events from the onset to the resolution of each accident, facilitating the classification of accident types, a pivotal aspect of the study. ace homework tutors. Additionally, the reports typically include information on accident location, prevailing weather conditions, and outcomes such as loss of life, injuries, and environmental pollution. Moreover, the global coverage of the entire world fleet provided by Lloyd's reports is essential for avoiding geographic or flag-specific biases in the analysis.

    ReplyDelete

One Nation, One electrical License

Electrical contractors are facing license problem when they bid for another state. Generally they are entitled to do work in particular stat...